Dyson Pure Hot + Cool Link™ Support - Purifying and heating modes | Dyson.com.au
Dyson Pure Hot + Cool Link™ purifier heater fan

 

Purifying and heating modes

Cooling mode

  1. Press the blue cooling mode button to enter cooling mode.
  2. The power button light will change from red to blue to indicate that you have entered cooling mode.
  3. To adjust the airflow speed use the airflow control button or use auto purification mode for automatic control.

Heating mode

  1. Press the red thermostat control button until the digital display shows the target room temperature.
  2. The power button light will change from blue to red to indicate that you have entered heating mode.
  3. To adjust the airflow speed use the airflow control button or use auto purification mode for automatic control.
  4. On first use, the purifier will default to a temperature 3°C higher than the detected room temperature. Thereafter, the purifier will remember the last target temperature set.

Heating mode display

  1. The target temperature indicator will be red while heating and once the target room temperature has been reached, the purifier will stop heating the air.
  2. The target temperature indicator will change to white when the target room temperature has been reached.

Auto purification mode

Auto purification mode adjusts the airflow speed according to the air quality in the room.

Auto purification mode display

When auto purification mode is enabled (indicated by an A symbol in the bottom left corner of the display), the on-board sensors will intelligently adjust the speed of the purifier according to the air quality. Increasing for poor air quality and reducing as the air quality improves.

Auto purification in cooling mode

Air quality below target

Auto purification in cooling mode

Air quality improving.

Auto purification in cooling mode

  1. If the air quality target is met, the A symbol will turn green and the numerical display will switch off.
  2. If the air quality worsens the A symbol will turn white and the purifier will automatically restart cleaning the room.

Auto purification in heating mode

  1. This display indicates that the air quality and room temperature are below target.
  2. When auto purification mode is used while in heating mode, the purifier is both purifying and heating the air.
  3. The purifier will display the target room temperature, not the fan airflow.

Auto purification in heating mode

  1. This display indicates that the air quality is below target but the target room temperature has been met.
  2. Once the target room temperature has been reached, the purifier will stop heating the air.
  3. If the air quality target has not been met, the fan will continue to run in order to keep purifying the air.
  4. If the room temperature falls below the target temperature, the purifier will start to heat again.

Auto purification in heating mode

  1. This display indicates that the air quality target has been met but is below the target room temperature.
  2. The purifier will continue heating until the target temperature is met.

Auto purification in heating mode

  1. This display indicates that the air quality and room temperature targets have been met.
  2. The purifier will continue to monitor the room and restart if the air quality worsens or the temperature falls below target.

Diffused mode

  1. Press the wide angle button to change from a personal directed airflow to a whole room airflow.
  2. Heating and cooling modes work in this mode.

Focused mode

  1. Press the narrow angle button to change from a whole room airflow to a personal directed airflow.
  2. Heating and cooling modes work in this mode.

Oscillation control

  1. To start the purifier oscillating, press the oscillation control button.
  2. To stop the purifier oscillating, press it again.
  3. The purifier will not oscillate when the control buttons are pressed.

Night mode

  1. When night mode is enabled the display will dim and after 5 seconds will fade to off.
  2. If the purifier is in auto purification mode, the airflow is limited to level 4 for quiet operation.

Night mode display

  1. A half moon symbol is illuminated in the bottom right corner of the display when night mode is enabled.
  2. When night mode is enabled the display will dim and after 5 seconds will fade to off.
  3. Please note other icons will not be visible in night mode.